Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
Have you been trying to find tips concerning How to Install a Bathtub?
Installing a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is easily accessible, the job can move rapidly; if you need to open a wall surface to remove the old bathtub and place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. Make sure you have qualified on your own for the job as well as fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is far better to consider employing one before you start. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you install a new tub in your shower room if you have actually currently bought a new tub and don't need to alter the setup of your previous water pipelines.
Your tools and material checklist must consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Safeguard the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bath tub should wait up until the bath tub has actually been used a minimum of when as this will settle it right into its last position.
Getting ready for the Setup
To start with, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to split a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can split relatively very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that report on A Step-by-Step Guide to Installing a Bathtub from an acquaintance on our other web page. Liked our post? Please share it. Let another person find it. Thanks so much for going through it.
Request An Appointment Report this page